Leading 10 common forklift accidents ， forklift operation ought to take note of these matters ！.

Don't underestimate the forklift at the office. If the procedure is bad, there will be major mishaps in minutes, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable width of the course and holds on the roadside shelf, which virtually triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these matters ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no obstacles that impede the security of driving, beep the horn initially and then start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress (air pressure) scale must be safe prior to starting.
3. When the forklift begins with a load, the driver must first verify that the load is secure and dependable.
4. The start must be slow-moving and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole should be tilted backwards. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the task website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork should not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be elevated other than when piling or filling. .
8. The elevation of the tons should not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with diseases or hide them.

filling and discharging.
1. When fork-loading items, the distance in between both forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift needs to be braked with the brake. .
4. The speed of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork idea should not touch various other items or objects. The tons needs to be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and hit difficult things with the fork head. .
7. When the Stand-on Electric Pallet Stacker forklift is working, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched Stand-on Electric Pallet Stacker off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not allowed under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the exact same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844